欢迎来到河南铭海机械有限公司!
您现在的位置:网站首页 > 新闻中心 > 正文 >
鳄鱼剪切机中英介绍
发布时间:03-10

 鳄鱼式剪切机是金属剪切机的一种,别名又叫鳄鱼剪、废钢剪断机、废钢剪切机、废铁剪切机、剪断机。鳄鱼式金属剪切机适用于金属回收公司、废钢厂、冶炼铸造企业对各种形状的型钢及各种金属结构进行冷态剪切,剪切出合格炉料。

Crocodile shearing machine is a kind of metal shearing machine. The alias is also called crocodile scissors, scrap shearing machine, scrap shearing machine, scrap iron shearing machine and shearing machine. The crocodile type metal shearing machine is suitable for metal recovery companies, scrap mills and smelting foundry enterprises to cut cold state shear for various shapes of steel and various metal structures, and cut out qualified furnace materials.
200重型快速废钢剪切机主要技术参数:
200 main technical parameters of heavy duty fast scrap shearing machine:
1、剪切刀长:1米。
1, cutting knife length: 1 meters.
2、剪切油缸规格:剪切油缸内径200-205毫米,剪切力可达100吨左右。
2, shear cylinder specifications: shear oil cylinder inner diameter 200-205 mm, shear force up to 100 tons.
3、电机配置:18.5千瓦电机或22千瓦电机。
3, motor configuration: 18.5 kilowatt motor or 22 kilowatt motor.
4、高压油泵规格:100YCY或者160YCY高压柱塞泵。
4, high pressure oil pump specifications: 100YCY or 160YCY high pressure plunger pump.
5、剪切最大张口尺度:剪切最大张口为350毫米到400毫米。
5, the maximum shear opening scale: the maximum shear opening is 350 mm to 400 mm.
6、剪切速度:每分钟8-10次剪切速度。
6. Shear speed: 8-10 shear speeds per minute.
7、剪切废钢种类:槽钢、工字钢、煤矿小道轨、角钢、汽车拆解大梁、螺纹钢、船板、普板厚度30毫米,圆钢直径600-700毫米等都可剪切。剪切厚度越厚剪切宽度越窄。
7, shear scrap type: channel steel, I-steel, coal mine track, angle steel, car disassembly beam, screw steel, ship plate, 30 millimeter thickness of the plate, 600-700 mm diameter of the round steel can be cut. The thicker the shear thickness, the narrower the shear width is.
(1)采用液压驱动,操作方便,维修简单。适用范围广,工作效率高、主机即可以安装于室内也可以安装在室外。
(1) hydraulic drive, easy operation and simple maintenance. Wide range of applications, high efficiency, the host can be installed indoors, can also be installed outside.
(2)工作刀口长度:500mm-1200mm,剪切力从60吨至250吨。适用不同规模,不同要求用户选择。
(2) working knife length: 500mm-1200mm, shear force from 60 tons to 250 tons. It is suitable for different sizes and requires users to choose.
(3)安装无须底脚螺丝,无电源的地方可用柴油机作动力。
(3) diesel engine can be used as a driving force for installation without necessary screws.
安全操作规程:
Safe operation procedure:
(1)设备应定人操作,其他人未经培训不得任意使用。
(1) equipment should be operated by others, and others can not be used without training.
(2)开车前应检查各部位是否正常,紧固件是否牢固。
(2) before driving, check whether the parts are normal and whether the fasteners are solid.
(3)禁止剪切未经退火的钢件、铸铁件、软质金属件、过薄的工件、长度小于100毫米的工件,以及超过剪刀长度的工件。 
(3) it is forbidden to cut unannealed steel, cast iron, soft metal parts, thin pieces, work pieces of less than 100 millimeters in length, and work pieces that exceed the length of scissors. It
(4)操作时,人体不准接近设备的传动部分及刀口,并应注意周围人员的安全,防止料翘起伤人。剪切时应尽量将料靠近刀里边剪切。剪较短料时,不得用手持工件送料,应采用夹钳送料。 
(4) when operating, the human body is not allowed to approach the transmission part and knife edge of the equipment, and the safety of the surrounding personnel should be paid attention to, so as to prevent the material from turning up and hurting people. When cutting, the material should be cut near the edge of the knife as far as possible. When cutting short material, no hand-held workpiece should be used for feeding. It
(5)设备运转时,操作人员不得擅自离开岗位,工作完毕或暂离岗位时,应切断电源。 
(5) when the equipment is running, the operator shall not leave the post without permission. When the work is completed or temporarily leave the post, the power shall be cut off. It
安装前准备工作:
Preparatory work before installation:
用户准备380伏电压及170-200kg液压油(46#)建议使用原装品牌的液压油如长城牌、昆仑牌、中石油牌、中石化牌等,做好以上准备工作即可接电按装投入生产。(注:北方夏季32#冬季46#;南方冬夏季均用46#)
Users prepare 380 volt voltage and 170-200kg hydraulic oil (46#) recommend the use of the original brand of hydraulic oil such as the the Great Wall brand, Kunlun brand, PetroChina brand, Sinopec, and so on, the above preparation work can be put into production according to the installation. (Note: northern summer 32# winter 46#; southern winter and summer 46#)

您可能对以下信息感兴趣?
联系方式

电话:151389-33533

QQ在线:

邮箱:cnsq@vip.qq.com

公司地址:河南郑州陇海西路与绕城高速交叉口

版权所有:河南铭海机械有限公司